Skip to content
Home >> Plumbing >> How to Install Foot Pedal Faucet? (10 Easy Step)

How to Install Foot Pedal Faucet? (10 Easy Step)

After Covid-19, everyone has started to understand the value of being hygienic. Similarly, the electric bills are also rising on mount Everest heights. Well, the solution to both these problems is a foot pedal faucet. However, installing them is never easy.

So, how to install foot pedal faucet? In a nutshell, it involves using a solenoid and plumbing parts to modify the complete sink’s water flow system. Additionally, a simple paddle may be used to regulate the entire water drip by connecting the water flow with the help of wires.

Nonetheless, the installation process is something that can never be told or understood in a single paragraph. So without any further ado, let’s get started with the installation of a foot pedal which requires no prior experience.

How To Install Foot Pedal Faucet

We will show you the simplest method to install a food pedal faucet that is covered in 10 small steps. Why so many steps? Well, each step only takes a minute to complete, and our mission is to go through every ins and outs of it. As a result, you can complete it with ease.

Step 1: Get Hold Of Solenoid Valves

A solenoid valve is the project’s core. They work when a small amount of voltage is passed through them. The valve opens up to pass water when a voltage is received.

Make sure you choose the dimensions according to your need. The flow rate of the water will be dependent on it.

Step 2: Wisely Choose The Hydraulic Fitting Adapter

The size of your solenoid valves and the fixtures under your sink will play a role in this. For each solenoid valve, you will require one of each hydraulic fitting adapter, for a total of four adapters.

According to the size of the fixture under your sink and the size of your solenoid, get hold of these hydraulic fitting adapters. If you have a half-inch fixture and an inch solenoid, then the hydraulic adapter should be bought accordingly.

For these dimensions, you should get a hydraulic adapter that has half-inch on one side and an inch on the other side.

On the other hand, if your solenoid valve is plastic and you use a connector, you might want to look for a rubber washer. As if it is not tightly sealed, the transition from brass to plastic may show a leak.

Step 3: A AC/DC Power Source For Your Pedal

In step 3, you will need to choose a power source for the pedal. It can be either direct line power or power from a battery. Your convenience is preferred here. Whatever you have near your hand, use that.

Step 4: Choosing and Drilling Pedal

You can make your pedal by using the useless things in your home. However, if you don’t know how to make one, then you probably shouldn’t. Buying one is the smart option here as they are quite cheap.

As soon as you get hold of the pedal and install the power wiring, it’s time to drill the pedal on the stand. Simply drill two holes in the stand and attach the pedal using screws.

Step 5: Setting Up The Solenoids

Your solenoid ought to have a flow direction indicator of some form. You should position the adapter so that the male end is on the arrow’s “to” side and the female end is on the arrow’s “from” side.

Step 6: Wiring

Here you must grab a wire according to the length you need to connect with the pedal. The more length you take, the merrier. Twist the wire up after trimming each end by approximately an inch. Connect the wires to the solenoid’s contacts in a loop.

Lastly, wrap the extra wire that is left around the valve itself.

Step 7: Taking Out The Water

We must locate the faucet’s shut-off valves. After turning them off, place a bucket underneath one of them and cut the hose connecting the faucet to the valve. Shake out any leftover water and then do the same for the other side.

Step 8: Connecting The Valve With Hose

Take the first solenoid assembly you have and affix it to the valve and hose that it goes with. As long as the coil is not excessively tight, it is acceptable to coil your hoses. As you tighten the hose, be careful not to bend it.

Do the same thing with other valves. Lastly, check to see whether you have any leaks by turning on each valve for a short amount of time.

Step 9: Getting The Pedal Ready

Finally, we are going to be needing to connect the other side of the solenoid assembly with the pedal. Simply take the wires that are open with the pedals and attach them with the solenoids using tape. That’s it; your foot pedal faucet system should be ready by now.

Step 10: Safety Check

You must do a safety check before leaving out the mechanic form. There would be leaks if you made an error in the steps. Don’t worry; it’s quite common. Thus, you should try to find the leaks by turning on the water flow from the source and using the pedal faucet several times.

If found, then you can use tape to fix the leak or redo that specific connection to fix them.

Conclusion

To conclude, that is all you need to know on how to install foot pedal faucet. If you follow these ten straightforward steps, then having a foot pedal water flow system will be present in less than half an hour.

Nevertheless, the most important factor to be aware of is the connections. If you don’t do it properly, then the system will not work as smoothly as expected. Moreover, giving you a leaky system.

Safety is equally important. Thus, wearing gloves on the steps and being extra careful with the AC/DC power of the pedal connection is vital.